Security Window Film, Basic 8 Mil Clear
Remlor Security Window Film is a PET film that will protect your family from broken glass caused by the average household accident, as well as deter someone from breaking into your home. A burglars goal is to get-in and get-out in a minimal amount of time, however, with Remlor Security Film installed correctly broken glass is held together, and takes much more force and time to enter through a window. In addition to security, this film had added benefit of protecting your house and family from the everyday accidents from a ball accidently thrown at a window, or a large glass window that someone may run into. Security film is designed to hold the glass together in the event of breakage, without obscuring vision. This film is 8 mil thick.
Our films are designed and constructed the same as the PET films discussed in this Discovery Channel Video
16 CPSC 1201
Safety Glazing |
Impact Resistance |
Designed to Pass
Category I & II |
16 CPSC 1201
Safety Glazing |
Weathering |
Meets Requirements of
Section 1201.4(e) 1(iv) & 2(iv) |
| ANSI Z97.1 |
Impact Resistance |
Designed to Pass
Unlimited Requirements |
| ANSI Z97.1 |
Weathering |
Designed to Meet Requirements
Of Section Z97.1.5.3.1 |
| BS 2606 |
Impact Resistance |
Designed to Pass
All Requirements |
ASTM D3330-96
ASTM G26 |
Peel Adhesion |
5.5lbs/in Pre-Weathered |
| ASTM D1044-94 |
Surface Abrasion
Resistance |
Delta Haze <3% |
| ASTM D635-88 |
Rate of Burning |
Material Does Not Stay
Ignited Long Enough for Reading |
| GSA's Method for Glazing Systems Subject to Air Blast Loading |
Bomb Blast Mitigation |
Designed to Perform to GSA
Hazard Level 3 Open Arena |
Dade County
Small Missile Test |
Wind Borne Debris |
Designed to Pass PA201, PA202 and PA203 with Anchoring |
All security films are installed on the interior surface of a window. The best method of installation is to remove the glass from the window frame, install the film, and reinstall the glass into the frame. The frame will act as an anchor to the film. If this is not possible, a bead of clear (or white, if preferred) silicone around the edge of the glass, about 24-48 hours after installation, is highly recommended. This will keep the glass and film firmly anchored in the frame if the glass is broken. |
|
Length: Sold by the Foot. Add the amount needed to your cart. Window Film ships in one continuous roll. Visible Light Transmittance: 90% Tensile Strength (ASTM D882-95a): 212 lbf. Propagation of Tear (ASTM 2582): 7 lbf. Graves Tear Test (ASTM 1004): 28 lbf. |
Window Film / Product Reviews
| (4 Ratings, 4 Reviews) |
Average Rating:
|
Inspection Passed!
Juan
(Colorado)
12/7/2011 3:58 PM
this was a one time purchase, to pass a final building inspection I needed to make the glass in the shower window to be resistant like tempered glass, your product was the only one I could find on the internet where you could buy effectively by the foot, everybody else had a minimum yardage to be sold. It works perfectly! Inspection Passed!
|
window film
Gene
(Tennessee )
9/16/2011 9:16 AM
Great product and easy to install
|
Positive Response!
Stan
(Virginia)
9/8/2011 10:28 AM
I reported an error in width received (19" was received 24" was ordered) for order no. XXXX dated 8/5/2011 and was told a replacement 4 yards would be shipped today. Just want to thank you for your positive response.
|
Clearly a good product
Jonas
(Los Angeles, California)
2/3/2011 11:48 AM
Yet to be tested but makes me much more secure about our kids chance of injury. Went on without too much difficulty and is virtually completely invisible, apart from the corners...the hardest to cut neatly.
|
Price: Starting at $10.49
Window Film for Safety from Broken Glass
|
Price: Starting at $14.95
Window Film For Extra Security
|
|
|
|
|
|
|